C5 Core Drilling Rig

Product model

Equipped with counterbalance valves for increased safety when positioning the mast.

The simple hydraulic system is easy to operate and maintain, and lift-to-shift levers provide additional operator safety.

Dired-coupled hydraulic pumps with a PTO-driven auxiliary pump allow for easy maintenance.

Rigid design provides superior performance and reliability even under the toughest conditions.

patented disc spring jaws with hydraulic open/spring close function ensuring fail-safe operation.

TECHNICAL INFORMATION

Prime Mover
	Metric	U.S.
Standard Unit	DEUTZ BF6M2012, liquid cooled, turbo changed, inter-Cooled, diesel engine
Displacement	6.06 L	370 in3
Power (maximum) at 2,500 RPM	147 KW	200 HP
Emissions Certification	EUⅢ	EUⅢ

Torque and RPM Ratings
(Hydraulic motor at maximum/minimum displacement, prime mover at 2,200 RPM)
	Speed (no load)	Torque (stall)
	RPM	Nm
1^st Gear	250 - 300	4 150 – 3 300
2^nd Gear	370 – 445	2 350 – 1 850
3^rd Gear	600 - 750	1 500 – 1 100
4^th Gear	1075 - 1300	900 – 700
NOTE: Drill head output speed and torque are infinitely variable in each gear range as indicated. Actual rotation speed is affected by engine RPM and hydraulic motor displacement setting.

Hydraulic System
	Metric	U.S.
Primary Pump	Axial piston, variable displacement load sensing, pressure compensated with low pressure standby.
Max Flow	220 L/min	58 gpm
Maximum Pressure (factory setting)	31 Mpa	4 495 psi
Secondary Pump	Axial piston, variable displacement load sensing, pressure compensated with low pressure standby.
Max Flow	132 L/min	34.8 gpm
Maximum Pressure (factory setting)	28 Mpa	4 060 psi
Tertiary Pump	Axial piston, variable displacement load sensing, pressure compensated with low pressure standby.
Max Flow	132 L/min	34.8 gpm
Maximum Pressure (factory setting)	28 Mpa	4 060 psi
Auxiliary Pump Ⅰ	Gear, matic axial clearance compensation mechanism assures high volumetric efficiency for long time
Max Flow	44 L/min	11.6 gpm
Maximum Pressure (factory setting)	20 Mpa	2 900 psi
Auxiliary Pump Ⅱ	Gear, matic axial clearance compensation mechanism assures high volumetric efficiency for long time
Max Flow	18 L/min	4.75 gpm
Maximum Pressure (factory setting)	20 Mpa	2 900 psi

Drill Head
Stand PQ – Hollow Spindle
Rotation Motor	SAM hydraulic motor – variable/reversible
Mechanical Transmission	Funk 5 speed
Ratios	1^st	4.37 : 1
	2^nd	2.896 : 1
	3^rd	1.78 : 1
	4^th	1 : 1
Final Drive	Straight cut gears
Ratio	2.564 : 1
Head lateral movement	Hydraulically operation
Hydraulic PQ Chuck	Hydraulically opened. Disk spring closed.
	Axial holding capacity of 244 640 N (55 000 lbf)
Drill Head Lubrication	Force fed bearings, oil bath for gears
Drill Head Lubricating Oil Filtration	25 micron high pressure oil filter

Drill Mast And Feed System
	Metric	U.S.
Feed Stroke	3.6 m	11.8 ft
Feed Pull	181 300 N	40 800 lbf
Feed Thrust	88 200 N	19 850 lbf
Rod pull	6 m	20 ft
Drilling Angle	30º off horizontal to 90º vertical down

Draw Works
	Metric	U.S.
Main Line Hoist	Double speed motor
Hook Load ( single part line)
Bare Drum	8 000 Kg	17 640 lb
Hoisting Speed (single part line)
High Speed (Bare Drum)	85 m/min	278 ft/min
Low Speed (Bare Drum)	50 m/min	164 ft/min
Main Hoist Cable	18mm	0.7 in
Minimum Breaking Strength	25 600 Kg	56 448 lb
Foot Clamp Capacity	PWT
Wireline Hoist
Line Pull
Bare Drum	1 500 Kg	3 300 lb
Full Drum	425 Kg	940 lb
Line Speed
Bare Drum	121 m/min	395 m/min
Full Drum	430 m/min	1 410 m/min
Drum Capacity (6mm swaged)	1 600 m	5 250 ft
Minimum Breaking Strength	3 420 Kg	7 540 lb

FLUID CIRCULATION PUMP
Single-Action Triplex Piston Pump, Manual shift, Pump Speed are infinitely variable.
	Metric	U.S.
Displacement	0 - 250 LPM	0 - 66 gpm
Pressure	0 - 7 Mpa	0 - 1 015 psi

Weight
Wet weight = 13 500 Kg	Consisting of : Power Unit Group DEUTZ BF6M2012, 6 cylinder Hydraulic Module Draw Works Grp. c/w 17,640 lb Main Line Hoist and Wireline Hoist c/w cable Hydraulic mast Raising (Independent) Lower Mast Assembly 2-Piece Lattice mast Assembly Rotation Unit Grp. c/w PQ Hydraulic Chuck / Head Guard Base Frame Fuel Tank Battery – 24V Operator Platform Hydraulic Foot Clamp – PWT Capacity

Options
Rod Racking Platform Hydraulic Leveling Jacks Crawler Track Unit – Max. travelling speed 4 Km/h Hot Weather Hydraulic Cooling Group Cold Weather Hydraulic Heating And Heat Preservation Group CE Certification Decals available in multiple languages Fluid circulation pumps ( diesel supply and pressure) Mud Mixer	WARNING: Do not operate this drill with rods racked in wind velocities in excess of